技术支持:0755-88856228
技术解决方案 所在位置:首页 >> 技术解决方案 >> Configure the Service Processor Network

Configure the Service Processor Network

出处:www.sun1860.com  分类:技术解决方案  发布:2017/10/31 13:43:59  阅读:(839)
摘要:


1. Configure the service processor using information from your network
administrator.
Your choices are:
■ dhcp - Set up the network connection with a dynamically created IP
configuration.
■ static - Set up the network connection with a static IP configuration.
a. If you choose to use a dynamically created IP address (use DHCP to retrieve
the network setting), set pendingipdiscovery to dhcp.
b. If you choose to configure a static IP configuration, set the parameters
pendingipdiscovery, pendingipaddress, pendingipgateway, and
pendingipnetmask as follows.
-> set /SP/network pendingipdiscovery=dhcp
Set ''''pendingipdiscovery'''' to ''''dhcp''''
52 Sun SPARC Enterprise T5140 and T5240 Servers Installation Guide ? May 2010
i. Set the service processor to accept a static IP address.
ii. Set the IP address for the service processor.
iii. Set the IP address for the service processor gateway.
iv. Set the netmask for the service processor.
This example uses 255.255.255.0 to set the netmask. Your network
environment subnet might require a different netmask. Use a netmask number
most appropriate to your environment.
2. Use the show /SP/network command to verify that the parameters were set
correctly.
For example:
-> set /SP/network pendingipdiscovery=static
Set ''''pendingipdiscovery'''' to ''''static''''
-> set /SP/network pendingipaddress=service-processor-IPaddr
Set ''''pendingipaddress'''' to ''''service-processor-IPaddr''''
-> set /SP/network pendingipgateway=gateway-IPaddr
Set ''''pendingipgateway'''' to ''''gateway-IPaddr''''
-> set /SP/network pendingipnetmask=255.255.255.0
Set ''''pendingipnetmask'''' to ''''255.255.255.0''''Servers Installation Guide ? May 2010
i. Set the service processor to accept a static IP address.
ii. Set the IP address for the service processor.
iii. Set the IP address for the service processor gateway.
iv. Set the netmask for the service processor.
This example uses 255.255.255.0 to set the netmask. Your network
environment subnet might require a different netmask. Use a netmask number
most appropriate to your environment.
2. Use the show /SP/network command to verify that the parameters were set
correctly.
For example:
-> set /SP/network pendingipdiscovery=static
Set ''''pendingipdiscovery'''' to ''''static''''
-> set /SP/network pendingipaddress=service-processor-IPaddr
Set ''''pendingipaddress'''' to ''''service-processor-IPaddr''''
-> set /SP/network pendingipgateway=gateway-IPaddr
Set ''''pendingipgateway'''' to ''''gateway-IPaddr''''
-> set /SP/network pendingipnetmask=255.255.255.0
Set ''''pendingipnetmask'''' to ''''255.255.255.0''''
-> show /SP/network
/SP/network
Targets:
Properties:
commitpending = (Cannot show property)
dhcp_server_ip = xxx.xxx.xxx.xxx
ipaddress = xxx.xxx.xxx.xxx
ipdiscovery = dhcp
ipgateway = xxx.xxx.xxx.xxx
ipnetmask = 255.255.252.0
macaddress = 00:14:4F:3F:8C:AF
pendingipaddress = xxx.xxx.xxx.xxx
pendingipdiscovery = static
pendingipgateway = xxx.xxx.xxx.xxx
pendingipnetmask = 255.255.255.0
state = enabled
Commands:
cd
Powering On the System 53
Note – After setting the configuration parameters, you must enter the set
/SP/network commitpending=true command for the new values to take affect.
3. Commit the changes to the service processor network parameters.
-> set /SP/network commitpending=true
Set ''''commitpending'''' to ''''true''''
Note – You can type the show /SP/network command again (after performing the
set /SP/network commitpending=true command) to verify that the
parameters have been updated.

联系方式
联系方式 深圳市众联达科技有限公司

电话:0755-88856228

手机:15889329885

传真:0755-29578940

Q Q:点击这里给我发消息

地址:深圳市龙华新区和平西路龙军工业区17栋401

深圳市众联达科技有限公司   版权所有:深圳市众联达科技有限公司  深圳市众联达科技有限公司
电话:086-0755-88856228    网址:www.sun1860.com 
地址:深圳市龙华新区和平西路龙军工业区17栋401    ICP备案号:粤ICP备16103267号-1
主营业务: SUN服务器 sun工作站 sun硬盘 sun内存 sun租赁 sun报价 sun维保